T301 Anti-chlorine non slip polyurea coating aquatic park

Product introduction polyaspartic coating

The component A is composed of an aliphatic polyurea modified resin, a pigment filler, an auxiliary agent and a small amount of an environmentally friendly solvent, and the component B is composed of an aliphatic isocyanate and a prepolymer. It can be hand-painted, rolled and high-pressure airless. The VOC emissions during construction are in line with national environmental protection policies. polyaspartic vs polyurea

Performance characteristics polyaspartic polyurea

Excellent UV resistance, good wear and slip resistance, and resistance to oxidation of organic chlorine in tap water. It has strong adhesion to manual polyurea and good waterproof effect. Suitable for making topcoats for waterproofing platforms in water parks.

Technical Performance		Quick Information
Hardness (Mitsubishi pencil)	1H	Solid Content (%)	70%
Adhesion (cross)	Level 1	Construction Period(25℃)	1-2h
Abrasion resistance (750g/500r)	≤0.04g	Dry Film Thickness	100-500µm
Water resistance (30d)	No abnormality	Theoretical Coverage	0.2kg/m² (when dry film is 150µm)
Organic gas resistant tap water (30d)	No abnormality	Surface Drying	1-2h
Acid resistance 240h (5%H₂SO₄)	No corrosion, No bubble, No shedding	Actual Drying	24h
Alkali resistance 240h (5%NaOH)	No corrosion, No bubble, No shedding	Re-coat Time	24-48h
UV resistant 1500h (xenon lamp)	No discoloration, No bubble, No shedding	Construction Methods	Brush, roller, airless spraying, spraying

Mixing :Waterproof coating A: curing agent B=2:1

Construction process:

Leveling the substrate → making a closed primer → roller coating or spraying polyurea coating → roller coating T301 anti-chlorine topcoat.

Mix component A and component B in a mass ratio of 2:1, roll or brush, and add about 5-10% diluent if necessary.

Shelf Life: The polyurea A component is 12 months, and the curing agent component B is 6 months (the product is qualified for expiration and can still be used).

Package: Polyurea coating 20kg curing agent 10kg

Water park brush-type polyurea waterproof construction plan

Construction conditions

Temperature is 5-35°C; Humidity <85%; Slope <5%; Flatness: 3m Ruler tolerance ≤3mm.

Reserve expansion joints: Generally, the seam is cut at a pitch of 6m, the slit width is 6mm, and the depth is 2cm;

Cement strength: The cement foundation strength must reach C25 or above; the curing time is not less than 28 days.

Construction process

1. Construction process:

Cut V-shaped seam → Polishing and smoothing base → Brush primer → caulking → Scratch-coated polyurea elastic mortar layer → Scratch-coated polyurea elastic coating

→ Partial repair → Roll-coated anti-chlorine anti-slip finish layer → Roll-on transparent anti-slip finish

2. Construction method

(1) Base surface treatment

A. Cut the V-slot and cut the expansion joint with a square of no more than 6x6m. The expansion joint width x depth = 6x 20mm.

B. Base surface grinding and cleaning: Grinding and leveling the rough and convex parts of the base surface with a sander to clean the scene.

C. Caulking: first clean the expansion joints. If the seam is deep or wide, use rubber particles or foam bottom, and then fill with polyurea elastic paint. For special recesses, repair with elastic materials and sand. .

D. Primer: After the foundation is sufficiently dry, brush the special primer T9302 and apply it to the base surface in two steps.

(2) Polyurea Polyaspartic elastic intermediate layer construction

Mix the A and B components of the polyurea elastic intermediate paint in proportion and try to use up within 30 minutes. During the construction, the paint should be scraped on the base surface with a toothed file or scraping. The thickness of each coating should not exceed 1mm, the second pass after 3-6h drying, and so on, until the thickness is required. Pay attention to the leveling effect when painting, to ensure the surface is smooth. T107 can be used as a layer of polyurea mortar, and then a T100/T109 coating.

(3) Surface layer construction: Mix the A and B parts of the top coat T301 in a ratio of 2:1 and apply it to the intermediate layer with a roller or spray gun.

(4) Apply anti-slip finish: Floors that require anti-slip treatment must be coated with anti-slip layers, such as amusement parks. Mix the A and B components of the anti-slip topcoat paint in a specified ratio and apply them to the layer by roller or spray gun.

3. Precautions

(1). During the construction process, the front coat must be trimmed before each process and the surface cleaned.

(2). After the site is laid, it needs to be maintained for more than 7 days before it can be put into use.

(3). Pay attention to the change of the day before the construction of each process. After the construction, ensure that there is no water immersion within 5-10 hours.

Polyaspartic coatings, We offer a mini sample kit and a money back guarantee.

Contact us if you need more details on Anti-chlorine Polyurea Coating. We are ready to answer your questions on packaging, logistics, certification or any other aspects about Non Slip Polyurea Coating、T301 Aquatic Park Polyurea Coating. If these products fail to match your need, please contact us and we would like to provide relevant information.

Product Categories : Polyurea Waterproofing > UMS-AUPT Polyurea System